전체 선택해제
총 89건 검색
본문검색 결과만 보기
-
Synthesis and characterization of carbon doped TiO₂ photocatalysts supported on stainless steel mesh by sol-gel method
JO. Tijani, OO. Fatoba, TC. Totito, WD. Roos, LF. Petrik 한국탄소학회 Carbon Letters 12 Pages
한국탄소학회 Carbon Letters 2017, Vol.22 6 48-59 (12 pages)
This study synthesized pure anatase carbon doped TiO₂ photocatalysts supported on a stainless steel mesh using a sol-gel solution of 8% polyacrylonitrile (PAN)/dimethylformamide (DMF)/TiCl₄. The influence of the pyrolysis temperature and holding time on the morphological characteristics, particle sizes and surface area of the prepared catalyst was investigated. The prepared catalysts were characterized by several analytical methods: high resolution scanning electron microscopy (HRSEM), energy... -
Thermo-electrical properties of randomly oriented carbon/carbon composite
Thakur Sudesh Kumar Raunija, N. Supriya 한국탄소학회 Carbon Letters 11 Pages
한국탄소학회 Carbon Letters 2017, Vol.22 3 25-35 (11 pages)
properties of low cost and rapidly produced randomly oriented carbon/carbon (C/C) composite. The composite body was fabricated by combining the high-pressure hot-pressing (HP) method with the lowpressure impregnation thermosetting carbonization (ITC) method. After the ITC method step selected samples were graphitized at 3000°C. Detailed characterization of the samples’ physical properties and thermal properties, including thermal diffusivity, thermal conductivity, specific heat and coefficient... -
The effects of carbon coating onto graphite filler on the structure and properties of carbon foams
Ji-Hyun Kim, Do Young Kim, Young-Seak Lee 한국탄소학회 Carbon Letters 5 Pages
한국탄소학회 Carbon Letters 2017, Vol.21 16 111-115 (5 pages)
Carbon foams (CFms) are of crucial importance in electrical and mechanical devices due to their high thermal conductivity used for eliminating high heat flow and maintaining low temperatures [1]. The most common CFms are types of aluminum alloys, copper and diamond. However, the mechanical properties of metal-based heat sink materials are difficult to control at temperatures over 550°C [2,3]. Thus, CFms are actively investigated as heat sink materials because of their good properties, such as... -
Green synthesis of fluorescent carbon dots from carrot juice for in vitro cellular imaging
Yang Liu, Yanan Liu, Mira Park, Soo-Jin Park, Yifan Zhang, Md Rashedunnabi Akanda, Byung-Yong Park, Hak Yong Kim 한국탄소학회 Carbon Letters 7 Pages
한국탄소학회 Carbon Letters 2017, Vol.21 7 61-67 (7 pages)
surfaces of obtained CDs were highly covered with hydroxyl groups and nitrogen groups without further modification. The quantum yield of as-obtained CDs was as high as 5.16%. The cell viability of HaCaT cells against a purified CD aqueous solution was higher than 85% even at higher concentration (700 μg mL?1) after 24 h incubation. Finally, CD cultured cells exhibited distinguished blue, green, and red colors, respectively, during in vitro imaging when excited by three wavelength lasers under a... -
Morphologies and surface properties of cellulose-based activated carbon nanoplates
Seulbee Lee, Min Eui Lee, Min Yeong Song, Se Youn Cho, Young Soo Yun, Hyoung-Joon Jin 한국탄소학회 Carbon Letters 7 Pages
한국탄소학회 Carbon Letters 2016, Vol.20 5 32-38 (7 pages)
CNPs showed a relatively high char yield when compared with MCC due to sulfate functional groups introduced during the manufacturing process. In addition, pyrolyzed CNPs (CCNPs) showed more effective chemical activation behavior compared with MCC-induced carbonaceous materials. The activated CCNPs exhibited a microporous carbon structure with a high surface area of 1310.6 m2/g and numerous oxygen heteroatoms. The results of this study show the effects of morphology and the surface properties of... -
Pitch-based carbon fibers from coal tar or petroleum residue under the same processing condition
Jiyoung Kim, Ui-Su Im, Byungrok Lee, Dong-Hyun Peck, Seong-Ho Yoon, Doo-Hwan Jung 한국탄소학회 Carbon Letters 7 Pages
한국탄소학회 Carbon Letters 2016, Vol.19 9 72-78 (7 pages)
a simple distillation under strong nitrogen flow, and further vacuum distillation to obtain a high softening point. Carbon fibers were produced from the above pitches by single-hole melt spinning and additional heat treatment, for oxidization and carbonization. Even though spinnable pitches and carbon fibers were processed under the same conditions, the melt-spinning and properties of the carbon fiber were different depending on the raw materials. A fine carbon fiber could not be prepared from... -
Cellulose-based carbon fibers prepared using electron-beam stabilization
Min Il Kim, Mi-Seon Park, Young-Seak Lee 한국탄소학회 Carbon Letters 6 Pages
한국탄소학회 Carbon Letters 2016, Vol.18 9 56-61 (6 pages)
measured. The structure of the cellulose fibers was determined to have changed to hemicellulose and cross-linked cellulose as a result of the E-beam stabilization. The hemicellulose decreased the initial decomposition temperature, and the cross-linked bonds increased the carbonization yield of the cellulose fibers. Increasing the absorbed E-beam dose to 1500 kGy increased the carbonization yield of the cellulose-based carbon fiber by 27.5% upon exposure compared to untreated cellulose fibers. -
Microwave-assisted pretreatment technologies for the conversion of lignocellulosic biomass to sugars and ethanol: a review
Pradeep Puligundla, Sang-Eun Oh, Chulkyoon Mok 한국탄소학회 Carbon Letters 10 Pages
한국탄소학회 Carbon Letters 2016, Vol.17 No.1 1 1-10 (10 pages)
Lignocellulosic biomass conversion to biofuels such as ethanol and other value-added bio-products including activated carbons has attracted much attention. The development of an efficient, cost-effective, and eco-friendly pretreatment process is a major challenge in lignocellulosic biomass to biofuel conversion. Although several modern pretreatment technologies have been introduced, few promising technologies have been reported. Microwave irradiation or microwave-assisted methods (physical and...
